www.evolutionbuild.com
13
GETTING STARTED
CAUTION! ALWAYS DISCONNECT THE
SAW FROM THE POWER SOURCE
BEFORE MAKING ANY ADJUSTMENTS.
Refer to the “Service Parts List Drawing”.
Install a blade as detailed in the “Installing or
Removing the Blade” section.
1. Mounting the Table Mitre Saw
WARNING: To reduce the risk of injury from
unexpected saw movement, place the saw
in the desired location either on a workbench
or other recommended leg set. The base of
the saw has four holes to mount the mitre
saw. If the saw is to be used in one location,
permanently fasten it to the workbench
or leg set using appropriate bolts with lock
washers and nuts.
1. Tighten the mitre and bevel locks.
2. Position the saw so other people cannot
stand behind it. Thrown debris could injure
people in its path.
3. Place the saw on a firm, level surface
where there is plenty of room for handling
and properly supporting the workpiece.
4. Support the saw so that the table is level
and the saw does not rock.
5. Bolt or clamp the saw to its support.
2. Installing or Removing the Blade
WARNING: Only use genuine Evolution
blades which are designed for this machine.
Ensure that the maximum speed of the
blade is compatible with the machine. Only
perform this operation with the machine
disconnected from the mains supply.
Note: It is recommended that the operator
considers wearing protective gloves when
handling the blade during installation or when
changing the machines blade.
1. Pull out the cutting head locking pin and
allow the cutting head to rise to its upper
position. (Fig. 1)
2. Remove the top blade guard with the
attached riving knife by loosening the socket
headed fixing screw (Fig. 2) and withdrawing
the riving knife upwards. The riving knife is
slotted for easy removal.
3. Push in the sprung loaded lower guard
operating pawl and slide it upwards along
the slot. The lower guard will rotate into the
machine exposing the blade. (Fig. 3)
4. Insert the supplied hex key into the rear
labeled arbor access port (Fig. 4) Ensure that
the hex key engages completely into the arbor
socket. Hold the hex key firmly so that the
machine arbor cannot rotate.
5. Using the supplied Blade Change Allen Key,
release the blade arbor screw and remove the
outer blade flange and the blade. (Fig. 4 & 5)
Note: The arbor screw has a LH thread.
6. Install the new 255 mm (10”) blade by
guiding it down through the table slot. Make
sure the rotation arrow on the blade matches
the clockwise rotation arrow on the upper
guard. (Fig. 6)
Note: The blade teeth should always point
downward at the front of the saw. Be careful
and patient, the blade is a very precise fit within
the machine. Sometimes extra clearance when
installing a new blade could be useful. If this is
the case raise the table height of the machine
as detailed in Operating Instructions – Table
Saw Configuration – 2 Adjusting the Table
Height.
7. Install the outer blade flange and arbor
screw. Ensure that the outer blade flange lugs
completely engage into the drive flats machined
on the machine arbor.
8. Whilst preventing the arbor from rotating
tighten the arbor screw using moderate force,
but do not overtighten.
9. Return the lower guard to the ‘safe’ position
by sliding the sprung loaded operating pawl
downwards along the slot until it locks in its
operating position.
10. Alternatively lower and cutting head to
its lowest position. The lower guard should
return automatically to its operating position
with the operating pawl correctly deployed.
11. Reinstall the riving knife and top blade
guard. Check that the riving knife is close to,
but does not foul, the saw blades teeth.
RAGE 6
(16 paginas)
(7 paginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales