RAGE Twin 155mm (6”) Disc Cutter Specifications
Motor (230V 50Hz) (Watts): 1200W
Motor (110V 50Hz) (Watts): 950W
RPM No Load (min
-1
): 4500 (230V) / 4000 (110V)
Max Cut Depth: 40mm
Weight: 9.6kg
Blade Dimensions
Maximum Diameter: 155mm
Thickness: Blade A: 1.5mm
Blade B: 1.7mm
Your Evolution Power Tools disc cutter is shipped complete.
Remove all contents from the box and inspect to ensure no
damage was incurred during shipping, and that the items
listed below are included.
DESCRIPTION QTY
INSTRUCTION MANUAL 1
125MM TCT BLADE (MOUNTED) 1 pair
SPANNER 1
ASSIST HANDLE 1
LUBRICATION UNIT (MOUNTED) 1
CAUTION! ALWAYS DISCONNECT THE DISC
CUTTER FROM POWER SOURCE BEFORE MAKING
ADJUSTMENTS.
Install the blade as detailed in the “INSTALLING/
REMOVING TCT BLADES” section.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms to the
power requirements specified on the product nameplate.
2. Power switch
Ensure that the power switch is in the OFF position. If
the plug is connected to a power receptacle while the
power switch is in the ON position, the power tool will
start operating immediately, which could cause a serious
accident.
3. Extension cord
When the work area is removed from the power source,
use an extension cord of sufficient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
4. Checking and installing the TCT Blades
Check the blade is a specified one and is not cracked,
broken or bent. Check the blade is installed securely. For
installation, refer to “Installing/removing TCT Blades”.
INSTALLING/REMOVING TCT BLADES
1. Installation
(1) Unplug the saw.
(2) Lay the saw down with the blade arbor pointing upward.
(3) Open the lower guard (see fig2).
(4) Place blade “A” onto the flange with the “A” clearly
visable (see fig1).
(5) Align the holes on the blades with the drive pins on the
flange and securely fit the blade onto the flange (see fig4).
(6) Place the blade “B” onto the adaptor with the blade
“B” easily visible, then thread lock nut onto shaft. DO NOT
tighten (see fig3).
(7) Turn the blades so that the holes in both blades are
lined up.
(8) Place the pin (included with the wrench) into the lined
up holes.
(9) Tighten the lock nut clockwise and then remove the
pin from the blades (see fig4). This will allow the blades to
turn freely.
(10) Carefully turn blades with your hand to be sure they
easily turn in opposite directions.
2. Removal
(1) Unplug the saw and allow blades to cool.
(2) Rotate the blades until holes in both the blades are
aligned. Then place pin attached to the wrench through
the holes in the blade. Unscrew Lock Nut by rotation in
counterclockwise and remove (see fig4).
(3) Open the lower guard (see fig2).
(4) Lift up and remove Blade “B”.
(5) Lift up and remove Blade “A” (see fig1).
CUTTING PROCEDURES
(1) Place this tool on the material to be cut and align the
premarked line and the TCT Blade.
(2) Turn on the switch when the TCT Blade is not touching
the material to be cut.
CAUTION
• Always check the TCT Blade before starting work.
Never use a TCT Blade which is cracked, broken or bent.
• Do not apply water or coolant to the TCT Blade.
• Start cutting only when TCT Blade reaches its maximum
speed.
• If the TCT Blade seizes or there is any abnormal noise,
immediately turn the power off.
• Never use the TCT Blade to cut zig zag or curved lines.
Never use the side surface of the TCT Blade. Never use to
perform inclination cutting.
www.evolutionbuild.com
6
SPECIFICATIONS
GB
ASSEMBLY
GB
OPERATION
GB
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales