Evolution FURY Twin 125 Manual de instrucciones descargar pdf (Pagina 4)

www.evolutionproject.com

neckties, rings, bracelets, or other jewellery which may get

caught in moving parts. Nonslip footwear is recommended.

Wear protective hair covering to contain long hair.

i) Always use safety glasses. Also use face or dust mask

if cutting operation is dusty. Everyday eyeglasses only have

impact resistant lenses, they are NOT safety glasses.

j) Secure work. Use clamps to hold work when practical.

k) Don’t overreach. Keep proper footing and balance at all times.

l) Maintain tools with care. Keep tools sharp and clean

for best and safest performance. Follow instructions for

lubricating and changing accessories.

m) Disconnect tools before servicing and when changing

accessories, such as blades.

n) Reduce the risk of unintentional starting. Make sure

switch is in off position before plugging in.

o) Use recommended accessories. Only use genuine

Evolution accessories.

p) Check for damaged parts. Before further use of the tool,

a guard or other part that is damaged should be carefully

checked to determine that it will operate properly and perform

its intended function - check for alignment of moving parts,

binding of moving parts, breakage of parts, mounting, and any

other conditions that may affect its operation. A guard or other

part that is damaged should be properly repaired or replaced.

q) Keep hands out of the path of the saw blades.

r) Never reach around the saw blades.

s) Turn off tool and wait for saw blades to stop before moving

workpiece.

t) Disconnect power before changing blades, servicing or

cleaning.

u) Never carry the tool by the power cord. Carrying the tool

by the power cord could cause damage to the insulation or

the wire connections resulting in the possibility of electric

shock or ﬁre.

SPECIFICATIONS

Fury Twin 125mm (5˝) Disc Cutter

Motor (230v or 110v 50Hz) (Watts): 850W

RPM No Load (min-1): 5500 min-1

Max Cut Depth: 28mm

Weight: 3.2kg

Blade Dimensions

Maximum Diameter: 125mm

Thickness: Blade A: 1.5mm

Blade B: 1.7mm

ASSEMBLY

Your Evolution Power Tools Twin Blade Saw is shipped

complete. Remove all the contents from the box and inspect

to ensure no damage has occurred during shipping, and that

the items listed below are included:

Description Qty

Instruction Manual 1

125mm Tct Blade (Fitted) 1 Pair

Spanner 1

Assist Handle 1

Lubrication Unit (Fitted) 1

CAUTION! ALWAYS DISCONNECT THE TWIN BLADE

SAW FROM THE POWER SOURCE BEFORE MAKING ANY

ADJUSTMENTS.

Install the blades as detailed in the ‘INSTALLING/

REMOVING TCT BLADES’ section.

OPERATION

Before commencing any operations, please check the

following:

1. Power source

Ensure that the power source to be utalized conforms to the

power requirements speciﬁed on the machines nameplate.

2. Power Switch

Ensure that the power switch is in the OFF position. If the

plug is connected to a power source with the switch in the

ON position, the machine will start operating immediately.

This could cause a serious accident.

3. Extension cord

When the work is remote from the power source, use an

extension cord of sufﬁcient thickness and rated capacity. The

extension cord should be kept as short as possible, and routed

so that it does not constitute a trip or other safety hazard.

4. Checking the Blades

Check that the blades are the speciﬁed ones, and are not

cracked, broken or bent. Do not use the machine if there is

any doubt about the integrity of the blades.

FURY TWIN

OPERATION

Kickback is the result of saw misuse and/or incorrect

operating procedures or conditions and can be avoided by

taking proper precautions as given below.

a) Maintain a ﬁrm grip with both hands on the saw and

position your arms to resist kickback forces. Position your

body to either side of the blade, but not in line with the

blade. Kickback could cause the saw to jump backwards, but

kickback forces can be controlled by the operator, if proper

precautions are taken.

b) If the blades are binding, or when interrupting a cut for any

reason, release the trigger and hold the saw motionless in the

material until the blades come to a complete stop. Never attempt

to remove the saw from the work or pull the saw backward while

the blades are in motion or kickback may occur. Investigate and

take corrective actions to eliminate the cause of blade binding.

c) When restarting a saw in the workpiece, centre the saw

blade in the kerf and check that saw teeth are not engaged

into the material. If saw blade is binding, it may walk up or

kickback from the workpiece as the saw is restarted.

d) Support large panels to minimise the risk of blade pinching

and kickback. Large panels tend to sag under their own

weight. Supports must be placed under the panel on both

sides, near the line of cut and near the edge of the panel.

e) Blade depth and bevel adjusting locking levers must be

tight and secure before making a cut. If blade adjustment

shifts while cutting. it may cause binding and kickback.

f) Do not use dull or damaged blades. Unsharpened or

improperly set blades produce a narrow kerf causing

excessive friction, blade binding and kickback.

g) Use extra caution when making a “plunge cut” into

existing walls or other blind areas. The protruding blade may

cut objects that can cause kickback.

Safety instructions for saws

a) Check lower guard for proper closing before each use. Do

not operate the saw if lower guard does not move freely

and close instantly. Never clamp or tie the lower guard into

the open position. If saw is accidentally dropped, the lower

guard may be bent. Raise the lower guard with the retracting

handle and make sure it moves freely and does not touch the

blade or any other part, in all angles and depths of cut.

b) Check the operation of the lower guard spring. If the guard

and the spring are not operating properly, they must be

serviced before use. Lower guard may operate sluggishly due

to damaged parts, gummy deposits, or a build-up of debris.

c) Lower guard may be retracted manually only for special

cuts such as “plunge cuts” and “compound cuts.” Raise

lower guard by the retracting handle and as soon as the blade

enters the material, the lower guard must be released. For all

other sawing, the lower guard should operate automatically.

d) Always observe that the lower guard is covering the blade

before placing saw down on bench or ﬂoor. An unprotected,

coasting blade will cause the saw to walk backwards, cutting

whatever is in its path. Be aware of the time it takes for the

blade to stop after switch is released.

Symbole Description

V Volts

A Amperes

Hz Hertz

Min-1 Speed

~ Alternating Current

No Load Speed

Double Insulated

Wear Safety Goggles

Wear Ear Protection

Only use genuine Evolution replacement blades.

Unauthorized blades may be dangerous! Keep the blades

securely fastened. Check for debris before installing any

new blades and do not use dull or broken blades. Check the

blades regularly for condition and wear. Damaged or worn

blades should be replaced immediately. Loose ﬁtting or

damaged guards must be replaced immediately. Beware of

ejecting chips as they may be HOT. Always make provisions

for safe handling of excess material.

To obtain an additional copy of your manual, please contact

Evolution Power Tools at:

UK 0870 609 2297

USA 1-866-EVO-TOOL

WEB www.evolutionpowertools.com

ADDITIONAL SPECIFIC SAFETY RULES

a) Keep guards in place and in working order.

b) Remove adjusting keys and wrenches. Form the habit

of checking to see that keys and adjusting wrenches are

removed from the machine before turning it on.

c) Keep work area clean. Cluttered areas and benches invite

accidents.

d) Don’t use in dangerous environment. Don’t use power

tools in damp or wet locations, or expose them to rain. Keep

work area well lit.

e) Keep children away. All visitors should be kept a safe

distance from the work area.

f) Don’t force the tool. It will do the job better and safer if

used at the rate for which it was designed.

g) Use proper extension cord. Make sure your extension cord

is in good condition. When using an extension cord, be sure

to use one heavy enough to carry the current your machine

will draw. An undersized cord will cause a drop in line voltage

resulting in loss of power and possible overheating.

h) Wear proper apparel. Do not wear loose clothing, gloves,

www.evolutionproject.com

SPECIFICATIONS

ADDITIONAL SPACIFIC SAFETY RULES

PROJECT

1 2 3 4 5 6 7

Instruction 1
FURY TWIN 2

Comentarios a estos manuales

Sin comentarios

Evolution FURY Twin 125 Manual de instrucciones Pagina 4

Comentarios a estos manuales

Relacionado con productos y manuales para Motosierras Inalámbricos Evolution FURY Twin 125