Evolution FURY Manual de instrucciones

210mm TCT Multipurpose Mitre / Table SawOriginal InstructionsRead instructions before operating this tool.www.evolutionfury.com®16.04.12_V9

www.evolutionfury.com10FURY 6 TABLE MITRE SAW SPECIFICATIONDesigned to cut: Mild SteelWood AluminiumPlasticTechnical DataMotor (230V ~ 50 Hz) (Watts)

www.evolutionfury.com11AssemblyYour Evolution Power Tools saw is shipped complete. Remove all contents from the box and inspect to ensure no damage w

www.evolutionfury.com12LH VIEW OF FURY 6 MITRE SAW CONFIGURATION

www.evolutionfury.com13LH VIEW OF FURY 6 TABLE SAW CONFIGURATION1. ON/OFF TRIGGER SWITCH (Inside handle)2. ON/OFF LATCHING SWITCHES

www.evolutionfury.com14GETTING STARTEDWARNING: ALWAYS DISCONNECT THE SAW FROM THE POWER SOURCE BEFORE MAKING ANY ADJUSTMENTS.Refer to the “Service Par

www.evolutionfury.com15NOTE: When the machine is re-positioned the operator should ensure that none of the rubber feet become detached from the machin

www.evolutionfury.com16TO CONFIGURE THE FURY6 FOR USE AS A MITRE SAWWARNING: Only carry out this procedure with the machine disconnected from the powe

www.evolutionfury.com17WORKPIECE SUPPORTS (Fig. 8)Workpiece supports can be fitted to both sides of the machine base if required. • Loosenthereleva

www.evolutionfury.com18To release the Cutting Head press and hold the Cutting Head Release Lever. Gently press down on the Cutting Head Handle to lowe

www.evolutionfury.com195. Chop CuttingThe Cutting Head is gently pushed down to cut through the workpiece.• PlacetheworkpieceontheRotaryTablea

www.evolutionfury.com203GB

www.evolutionfury.com20NOTE: Always make a ‘dry run’ with the machine switched ‘off’ so that the path of the blade can be checked. Some Bevel and Comp

www.evolutionfury.com21TO CONFIGURE THE FURY6 FOR USE AS A TABLE SAWWARNING: Do not cut metal or metallic materials when the machine is configured as a

www.evolutionfury.com22FENCE ASSEMBLY (Fig. 19)The Fence Assembly consists of two (2) main parts:• TheAngleGauge.• TheRipFenceFacePlate.NOTE:

www.evolutionfury.com23• TightentheAngleClampingScrew.• AdjusttheAngleGaugePointerifnecessary to point exactly to the 900 index mark. • U

www.evolutionfury.com24NOTE: A workshop dust extraction device can be connected to the extraction port found at the rear of the machine if required.2.

www.evolutionfury.com25Riving KnifeThe Riving Knife is a very important component and comes factory fitted and correctly aligned and adjusted. The Rivi

www.evolutionfury.com26• Usethepinspanner(provided)toholdthe outer blade flange.• Usethehexkey(provided)tounscrewthe arbor screw. (Fig.

www.evolutionfury.com27NOTE: To check and adjust the Bevel Angles the machine must be in Mitre Saw configuration.00 BEVEL ANGLEAt 00 Bevel Angle the bl

www.evolutionfury.com28FENCE ADJUSTMENT (Fig. 33a & 33b)The Fence is fastened to the machines base by two (2) socket head screws, one on either si

www.evolutionfury.com29

www.evolutionfury.com3TABLE OF CONTENTSEC - Declaration of Conformity 4Important Information 512 Month Limited Warranty 5General Safety Rules 5Ad

www.evolutionfury.com30

www.evolutionfury.com31

UK ADDRESS:Evolution Power Tools, Venture One, Longacre Close, Holbrook Industrial Estate, Sheffield, S20 3FRTEL: +44 (0) 114 251 1022FAX: +44 (0) 114

www.evolutionfury.com4EC - DECLARATION OF CONFORMITYWe, manufacturer and importerEvolution Power Tools Ltd.Venture OneSheffieldS20 3FRDeclare that the

www.evolutionfury.com5IMPORTANTPlease read these operating and safety instructions carefully and completely. For your own safety, before using this eq

www.evolutionfury.com6not use tools for purposes not intended; for example do not use circular saws to cut tree limbs or logs. 8. Dress properly. Do n

www.evolutionfury.com7ADDITIONAL SAFETY INSTRUCTIONS FOR YOUR TABLE MITRE SAW WARNING: Be sure to read and understand all instructions. Failure to fol

www.evolutionfury.com822. Never stand on this tool. Serious injuries could occur if this tool tips over and you come into contact with the saw blade.

www.evolutionfury.com9SAFETY LABELS & SYMBOLSWARNING: Do not operate machine if warning and/or instruction labels are missing or damaged. Contact